The sibling article covers grill cutouts brand-by-brand. This one is the pre-pour checklist for the WHOLE island — grill, side burner, fridge, vent hood, storage drawers, insulated jacket gap, counter overhang. Twelve measurements. Miss any one of them and the stone comes back out.
Why twelve measurements, not three
Most planning-stage search results stop at the grill cutout — width, depth, height. That is three of the twelve measurements that actually matter. The other nine are the ones that break the project once the stone is set. A side burner cavity cut to the wrong depth. A fridge that overheats on day two because the ventilation gap vanished. A vent hood mounted too low that smoke-stains the island face every time someone sears. Storage drawers that cannot accept a standard 23-inch depth. The hood clearance in front that was never checked, so the control panel gets a steam bath with every cook.
The companion piece,Built-In Grill Cutout Dimensions by brand, is the grill-only deep dive. This one is the whole-island planning checklist — cross-brand, every appliance type, pre-concrete. Updated November 2026.
Cross-section elevation. Dashed orange outline around the grill shows the insulated jacket gap most DIY builders cut too tight.
The twelve measurements
1–3. Grill cutout width, depth, and height
Start with the grill because everything else sizes around it. Every brand on this chart publishes its own cutout rectangle, and the differences are real enough that a counter cut for aBull Angus 30" will not fit aCoyote SL-Series 30", even though both are nominally 30-inch grills. Bull wants 20 3/4-inch depth. Coyote SL wants 23 1/4. Hestan wants 23 3/4. The depth spread across brands is bigger than the width spread — plan to the actual grill, not to a generic 30 by 20 opening. The full brand-by-brand breakdown lives inthe sibling chart article; the quick-reference table farther down this page covers the common sizes.
4. Counter overhang in front of the grill
Six inches is the minimum. Ten to twelve inches is where experienced installers land. The hood swings on an arc when opened, and the apex of that arc sits above the counter edge, not above the grill body. Measure the fully open hood height before pouring. A 36-inch grill with a 20-inch open-hood arc wants different front clearance than a 42-inch grill with a 24-inch arc.
5. The insulated jacket gap (the one most DIYers miss)
This is the measurement that costs the most rebuilds. Every built-in gas grill ships with an insulated firebox jacket — a double-wall shell that keeps combustibles cool and lets the grill pass UL listing for enclosed installs. That jacket needs an air gap on all four sides between the jacket's outer shell and the island surround. One to two inches is typical, brand-dependent. Bull and Coyote both spec one inch minimum.Hestan is the exception — its insulated jacket is engineered for zero-clearance to combustibles, so the gap requirement effectively disappears.
Brochures almost never picture the jacket gap because it sits hidden under the counter lip. DIY builders measure the grill head, cut the stone to that width, and discover on install day that the jacket does not drop in. Always add the jacket gap to BOTH the cutout width and the cutout depth before templating the stone.
Rule of thumb for jacket gap: if you are building with any brand other than Hestan, add 2 inches to the published cutout width and 2 inches to the published cutout depth. A 36-inch Coyote with a published 36 1/16 by 20 1/4 cutout actually wants a 38 by 22 1/4 opening cut in the stone, then the finished jacket drops in centered with a 1-inch gap on all sides.
6–7. Side burner cutout width and depth
Side burners are the appliance most frequently added as an afterthought, and they are the cavity most frequently cut wrong. Bull side burners want 12 inches wide by 20 inches deep. Coyote wants 13 1/4 by 20 1/4. Summerset wants 13 by 20 1/2. Hestan wants 13 1/2 by 23 1/4. The depth is the sneaky dimension — Hestan's is three inches deeper than Bull's, which means the Hestan side burner cannot drop into a Bull-sized hole without recutting the island wall from the back.
Build the island to the brand you have already picked for the grill, and specify the matching brand's side burner — matching brand's drop-in dimensions line up and the counter edge trim is consistent. Mixing brands between grill and side burner is legal, but the counter cutouts need separate templates.
8–9. Fridge cutout and ventilation gap
Outdoor refrigerators are not indoor refrigerators in a jacket. Specify an outdoor-rated SKU, cut the cutout to the manufacturer's dimensions, and add a half-inch of ventilation gap on both sides. A lot of built-in fridges also want a half-inch at the top for the compressor to breathe. The compressor on an outdoor fridge vents through a front grille at the bottom of the unit — do NOT box in the grille with trim or the fridge shuts down on thermal overload within a week.
Common cutout sizes: 15 inches wide for a 3.2 cubic foot single-door, 24 inches wide for a 5.5 cubic foot double-door or double-drawer. Depth is almost always 23 to 23 1/2 inches across every outdoor-rated brand, so the island depth decision is grill-driven, not fridge-driven. If the grill wants 24 inches of depth, the fridge drops in without a concern.
10–11. Vent hood mount height and width
If the island sits under a pergola, a lanai roof, or any enclosed overhead, a vent hood is not optional — code requires it in most jurisdictions for any island with a cooking appliance above a certain BTU threshold. The industry baseline is 36 inches from the cooking grate to the bottom lip of the hood for a 36-inch grill. Taller cooks or undersized hoods want 42 inches.
Hood width is the measurement that gets undersized the most. The hood should match or exceed the grill width. A 36-inch grill wants a 36-inch or 42-inch hood. ABull Diablo 46" wants a 48-inch or 54-inch hood. Narrow hoods over wide grills leak smoke at the ends, stain the surround, and fail to pull heat on sear-burner work. Buy wider than the grill, not narrower.
12. Storage drawer cutout
Twenty-three inches of depth is the almost-universal drawer cutout depth across the four brands on this chart, because the drawers share counter-depth real estate with the grill firebox above them. Height varies — single tool drawers at 10 inches, three-drawer stacks at 24 to 30 inches, double-walled roll-out trash units at 24 inches. The spec that is NOT universal is the width: Summerset runs 15-inch and 20-inch standard widths; Bull runs 15-inch, 20-inch, and 24-inch; Coyote and Hestan both run 24-inch as their singleton standard. Pick the brand for its grill then order the drawer in the matching width — it will be cheaper than the cross-brand workaround.
Cross-brand quick-reference table
The twelve measurements across the four built-in brands we stock. Width × Depth × Height in inches. Use this as the fast-glance reference during island templating; the deep-dive brand-by-brand breakdown lives inthe sibling cutout article.
Measurement
Bull BBQ
Coyote
Summerset
Hestan
36" built-in grill (W × D × H)
38 1/4 × 20 3/4 × 9 3/4 (Brahma)
36 1/16 × 20 1/4 × 10 (C/CL)
37 3/4 × 20 1/2 × 10 (TRL38)
35 1/2 × 23 3/4 × 11
30" built-in grill (W × D × H)
30 1/2 × 20 3/4 × 9 3/4
30 1/16 × 23 1/4 × 10 (SL)
29 3/4 × 20 1/2 × 10 (SBG30)
29 1/2 × 23 3/4 × 11
Insulated jacket gap
1" minimum
1" minimum
1" minimum
0" (zero-clearance jacket)
Gas stub position
left-rear
center-rear
left-rear
center-rear
Island ventilation requirement
Two 10 sq in opposing vents
Two 10 sq in opposing vents
Two 10 sq in opposing vents
Factory vent panel
Side burner cutout (W × D)
12 × 20
13 1/4 × 20 1/4
13 × 20 1/2
13 1/2 × 23 1/4
Counter overhang in front of grill
6" minimum
6" minimum
6" minimum
6" minimum (10–12" preferred)
Vent hood height above grate
36" minimum
36" minimum
36" minimum
36" minimum (42" preferred w/ wall)
All dimensions in inches. Width × Depth × Height. Pulled from current manufacturer install manuals as of November 2026.
The three install-order mistakes that force a rebuild
Pouring the counter before the grill is picked
A committed cutout with no grill picked is the worst constraint in an outdoor-kitchen build. The brand-locked measurements — gas stub position, vent panel orientation, jacket depth — cannot be shimmed. If the grill has to change after the pour, something gets re-cut. Lock the exact grill model before the stone goes down.
Running gas to the wrong side of the cavity
Bull and Summerset want left-rear gas. Coyote and Hestan want center-rear. Rough in the wrong side and the plumber comes back twice. Spec the stub to the grill brand, not to a generic "rear" position.
Omitting the vent openings in the island walls
Every brand on this chart requires airflow into the enclosed island cavity — either two 10-square-inch opposing vents cut into the side or back panels, or factory vent panels forHestan. Skip the vent openings on a propane install and heavier-than-air gas pockets the enclosure. Code violation, ignition hazard, and inspection failure in one move. Cut the vent holes during framing, not after the stone is set.
Which brand to pick before you measure
If the island is going against a wood-framed exterior wall, pick Hestan — the zero-clearance jacket is what makes a built-in legal there without a 12-inch stone backsplash. If the island is free-standing in the middle of a patio and the budget is the constraint, pickBull BBQ orSummerset — both tolerate the standard non-combustible surround and come in at a lower price point per cutout inch. If the design priority is the control-panel look and the warming-drawer integration,Coyote is the match — the C-Series and SL-Series share interior architecture with Coyote's refrigeration and drawer line, so the counter-edge trim stays visually consistent across every appliance.
Every number on this page is pulled from the current install manual linked from each product's PDP, not from marketing brochures. Manufacturers revise cutout dimensions quietly, in 1/8 and 1/4 inch tweaks that never make it to the brochure. When a spec changes, this page gets rebuilt the same day. If anything here disagrees with the physical manual that came out of the box, trust the manual and let us know — the chart gets fixed inside 24 hours.
Frequently Asked Questions
How many measurements do I need before pouring a built-in grill island?+
Twelve, if the island carries a grill plus a side burner, a fridge, a vent hood, and storage drawers. Grill cutout is three (width, depth, height). Add counter overhang in front of the grill, insulated jacket clearance on all four sides of the firebox, side burner cutout width and depth, fridge cutout and ventilation gap, vent hood mount height and width, and storage drawer cutout. Miss any one of those and the appliance either does not fit or does not pass inspection.
What is the insulated jacket gap and why do most DIY builders miss it?+
Every built-in gas grill ships with an insulated firebox jacket that still needs an air gap around all four sides — typically one to two inches of open space between the jacket's outer shell and the island surround. Brochures rarely picture it because the gap sits hidden under the counter lip. DIY builders measure the grill head, cut the stone to that width, and discover on install day that the jacket does not drop in. Always add the jacket gap to the cutout width and depth before templating.
How much ventilation does an outdoor refrigerator need in a built-in island?+
Outdoor-rated refrigerators specified for built-in use need a half-inch of ventilation gap on both sides and typically a half-inch at the top, plus a front-vented compressor grille that cannot be blocked. Indoor-rated refrigerators are not legal for enclosed outdoor installs — they vent out the back and overheat in an enclosed cavity. Always buy the outdoor-rated SKU and cut the cavity to the manufacturer's vent spec, not a generic appliance-cutout dimension.
How high should a vent hood sit above the cooking surface of a built-in grill?+
Thirty-six inches above the cooking grate is the industry baseline for a 36-inch grill, measured from the cooking grate to the bottom lip of the hood, and adjusted up to 42 inches for taller cooks or if the hood is undersized relative to the grill width. The hood width should match or exceed the grill width — a 36-inch grill wants at least a 36-inch hood, and a 42-inch grill wants a 42-inch or 48-inch hood. Narrow hoods over wide grills leak smoke at the ends.
What is the right counter overhang in front of a built-in grill?+
Six inches minimum, ten to twelve inches preferred. The grill hood swings on an arc when opened, and the apex of that arc sits above the counter edge, not above the grill body. Measure the fully open hood height before pouring and give the hood at least two inches of air at full open. Ten to twelve inches of overhang also keeps the control panel from steam-burning when the hood vents during normal cooking.
Can I size the island cutouts before I pick the exact appliances?+
Risky but survivable if done right. Specify every cutout to the widest and deepest model under consideration in each category, then use stainless filler frames to shim to the actual model. A half-inch filler panel is easier to live with than re-cutting stone. The two measurements that cannot be shimmed are gas stub position and vent panel location — those are either right or they require re-plumbing and re-cutting the island wall, so lock the specific grill brand down before the gas line runs.
Ash — Ash writes the buying guides at FirePits.com — years of specifying fire features on residential installs, from urban patios to mountain properties.